Auto Ventshade [AVS] Aeroskin Hood Protector | Fits 2019 - 2023 Ford Ranger | Low Profile Deflector / Bug Shield - 1 pc., Smoke | 322166

Fairly easy to install and works as advertised.

1st, AVS misboxed my 1st order! Whomever boxed mine transposed numbers around, and I got one for a 2008 Santa Fe, which is very similar! Amazon made it right! PLEASE follow Mr. Fixit instructions(1st post), except place a piece of scotch tape over the retainer that goes into the hood. Then poke the hole through it so you can insert the plastic screw for the install. BTW, holes on the deflector lined up perfectly! Also, by all means place a couple of LARGE bath towels or a sheet over the front and over the engine! YOU WILL drop a screw!! When that happens, it's GONE! ONE more piece of advice, I LOVE my wife, but maybe she isn't the best partner on these type of projects! Consider another another helper!The low profile shield covers the front of the hood perfectly and isn't seen from the drivers seat!Finally, I have a J7 magnetic Ranger and like everyone else's, it looks GREAT! I highly recommend this shield to protect the front of the hood! It fits fine and I didn't need to readjust the hood latch, mine closes with no additional effort.Great value for the money!

The media could not be loaded. Looks like factory installed, just the right size and very easy to install. Some say the need to manipulate the hood hinge, but in my case with a Ford Ranger XLT 2019, the fit was perfect and no need to adjust hinge…. One thing could be better are the plastic screws and also that you get just the number needed, so if you drop one or bend one you are out of luck, no extras …. I had to install a metal one I happened to have around

The only reason I gave it 4 stars instead of 5, is because there were no instructions in the box, I did watch a very good video on YouTube showing how to install it. The bug deflector 2 itself was fairly easy to install and does a very good job. It also looks good on my truck.

This is high quality and easy and quick to install. The material is incredibly strong. They are rock solid when driving on highways. I have always used bug deflectors on my trucks. It’s been a while since installing my last one. Wasn’t sure how this one actually attached to hood. YouTube showed using double sided tape. Not the case for these. They are attached directly to under side of hood with supplied pop rivets. Super strong. Highly recommended them as top of the line bug and stone deflector.

I don’t usually write a review when I first get a product. They almost always look good or fit good when you first get it. This deflector still looks good and it still fits great…

So this review is about my Amazon experience. I ordered this item twice and both time it arrived damaged. The box had literally been ripped in half and there was gravel & small rocks in the box that scratched the deflector. Tape was also coming off, making it unusable. I ordered a replacement and it was just as bad. Like they had dragged it behind the truck! Finally, I ordered it through Autozone…saved myself $42 and the box and deflector were in new condition when they arrived. Amazon took over a week (even with Prime) and Autozone had it to me in 2 days. Deflector itself is a quality product - easy to install and nice looking. This is the third vehicle we’ve purchased it for and couldn’t be happier with the no drill installation.

Easy to install. Installed it in about 20 minutes without assistance. I recommend marking the clip areas with masking tape instead of a grease pencil. Once the shield is installed just pull the small pieces of tape off. Photos are approximately 4 weeks after installation.

Great product fast delivery

Super sticky, fit like a glove and look awesome.

Vous devrez installer un on ondulateur car la radio griche après installation

The bug/stone defector looks great, fits perfectly and is a quality product. There are some great You Tube installation videos on line that give some great tips. I gave it five stars, but I did find that the screws that came with it had very soft heads and I almost stripped one and did strip another, with very little pressure. One of the you tube videos suggests a tool to help take out the existing hood plugs, that I found very helpful.

Fit parfaitement le ranger 2019. Beau look . Collé à la carrosserie. Pas de vissage ou de boulons ou de percage. Du bon vieux 3m. Laisser sécher avant usage pour que ça adhère bien et c tiguidoo!